首页 >> 安全评价 >>消防验收 >> 消防产品(探测器/报警器)检测
详细内容

消防产品(探测器/报警器)检测

24小时检测认证专家电话:

      15905657669

检测报告

  注:不接受个人委托测试。

  检测周期:7-15个工作日检测报告。(加急当日出具报告)


检测报告用途

       用于产品认证;

       用于工程、科研、高新成果转化等项目验收;

       用于投标加分;

       生产企业证明产品符合国家相关标准,制作为产品图册用于企业样册宣传展示。


检测范围

 

一、消防产品检测标准:

1、 国标标准:
GB 4715  点型感烟火灾探测器
GB 20517 独立式感烟火灾探测报警器
GB 4716  点型感温火灾探测器
GB 19880 手动火灾报警按钮
GB 4717  火灾报警控制器
GB 17429 火灾显示盘
GB 16806 消防联动控制系统
GB 16808 可燃气体报警控制器
GB 14003 线型光束感烟火灾探测器
GB 15322.1 可燃气体探测器 第1部分:工业及商业用途点型可燃气体探测器
GB 15322.2 可燃气体探测器 第2部分:家用可燃气体探测器
GB 15322.3 可燃气体探测器 第3部分:工业及商业用途便携式可燃气体探测器

2、国际标准:
EN 54-2   Fire detection and fire alarm systems - Part 2: Control and indicating equipment
EN 54-4   Fire detection and fire alarm systems - Part 4: Power supply equipment
EN 54-5   Fire detection and fire alarm systems Part 5: Heat detectors-Point heat detectors
EN 54-7  Fire detection and fire alarm systems Park 7:Smoke detectors-Point smoke detectors that operate using scattered light, transmitted light or ionization
EN 54-11  Fire detection and fire alarm systems - Part 11: Manual call points
EN 54-16  Fire detection and fire alarm systems-Part 16: Voice alarm control and indicating equipment
EN 14604     Smoke alarm devices
EN 50291-1   Gas detectors - Electrical apparatus for the detection of carbon monoxide in domestic premises-Part 1:Test methods and performance requirements
EN 50194-1  Electrical apparatus for the detection of combustible gases in domestic premises-Part 1: Test methods and performance requirements
BS 5446-2    Fire detection and fire alarm devices for dwellings. Specification for heat alarms
AS 3786      Smoke alarms using scattered light, transmitted light or ionization

二、主要测试项目:
1、 烟感火灾报警探测器:报警响应阈值(重复性、方位性、一致性)、环境试验(环境光线、高/低温、SO2腐蚀、振动、冲击)、EMC、火灾灵敏度等。
2、 温感火灾报警探测器:报警响应时间、动作温度、环境试验(高/低温、交变湿热、SO2腐蚀、振动、冲击),EMC等。
3、 手动火灾报警按钮:动作性能试验、环境试验(高/低温、SO2腐蚀、振动、冲击)、EMC、雨淋试验等。
4、 可燃气体探测器:气体报警器种类:甲烷、丙烷、氢气、一氧化碳等。探测器报警动作值、量程指示偏差、绝缘电阻、耐压、环境试验(高/低温、SO2腐蚀、振动、跌落)、气体干扰试验、EMC、雨淋试验等。
5、 报警控制器:功能试验、安全性能(绝缘电阻、泄漏电流、电气强度)、EMC、环境试验等。

三、主要测试设备:
烟温一体测试烟箱、火灾燃烧实验室、可燃气体环形配气箱


检测流程

  1、寄样

  2、免费初检

  3、报价

  4、双方确定,签订保密协议,开始检测

  5、完成检测:检测周期会根据样品及其检测项目/方法会有所变动,可咨询工程师

  6、出具检测报告,后期服务。


以上是关于产品检测的相关介绍,如有其他检测需求可以咨询实验室工程师帮您解答。

由于篇幅有限,仅展示部分项目,如需咨询详细检测项目,请咨询在线工程师


官网微信公众号

客服微信号

技术支持: CLOUD | 管理登录
seo seo